For the home handyman: Ariston water heater 80 liters instructions

Advantages of Ariston technology

Like all Ariston equipment, water heaters from this company have many advantages:

1. The first of them can be called a stylish design that helps to decorate any interior. Moreover, each of the models is created in accordance with the latest technologies.
2. The Ariston 80 water heater has the longest service life. This effect was achieved due to the fact that the internal walls of the storage tank are covered with a layer of modern material that protects the tank from plaque and rust.
3. Built-in latest dividers prevent mixing of already heated and cold water. This helps maintain the temperature of the liquid. The Ariston heater is also protected from overheating thanks to built-in temperature control sensors.
4. The presence of a protective shutdown device that is triggered in moments of sudden voltage changes.
5. Using Ariston water heaters, users can significantly save on gas or electricity consumption. This is facilitated by the presence of thermal insulation, which keeps the water hot for a long period of time.
6. Many models of water heaters are equipped with protection against the appearance of bacteria, which makes it possible to use purified water. If there is no water in the system, then you don’t have to worry about the water heater turning on, since it is equipped with special protection.

Design of ARISTON water heaters for 80 liters

The external simplicity of any water heater carries with it the same uncomplicated internal structure. The difference can only be observed in the external design and materials from which the heater is made. The external structure of the body can be made in a cylindrical or flat shape.

Any water heater has:

• The internal tank is a boiler into which cold water flows. It is framed by an outer casing.
• The water that enters the tank is heated by a built-in heating element . To heat water faster, the boiler may have two heating elements.

• Thermal insulation layer , which is present between the body and the boiler, performs the function of a thermos, which allows you to maintain the water temperature longer.
• Water enters the tank through a shortened pipe with a divider . The heated water is supplied by the outlet pipe.
• Magnesium anode built into the Ariston 80 water heater prevents the deposition of mineral salts on the walls of the inside of the tank. This element is replaced as needed.

• During heating, when the set temperature is reached, the thermostat , which automatically interrupts the power circuit.
• If the heating element is turned on and the water temperature drops below the set values, then the configured thermal relay .
• The voltage indicator (indicator light) allows you to control the operation of the water heater
• The built-in thermometer makes it possible to monitor changes in temperature.

The Ariston 80 storage water heater, which belongs to the flat horizontal models, has the same typical internal structure.

We recommend Autonomous water supply for a private house from a well, diagrams

Shuttle Ariston electric water heater: instructions for using boilers, diagram

After purchasing such an assistant as an Ariston 80-liter water heater for your home, the instructions should be the first document that should be carefully studied before you start using it. This will help you understand all the nuances of working with the boiler and extend the operating life of the device.

An Ariston 80 liter water heater is used to supply the house with hot water. Many positive characteristics contribute to the choice of this series of heaters.

The Ariston 80 v water heater has the same design and instructions for use as all models in this series. Installation should be carried out in accordance with the attached diagrams.

The lineup

Flat boiler Ariston

The range of water heaters is quite huge and is constantly being updated. They are very compact, although they have a large displacement. For a family of four, an 80-liter capacity is ideal.

Square tanks with mechanical controls are very common. The only drawback is the unimproved fastening mechanism.

There are also models with a maximum capacity of 100 liters. Such units are capable of providing industrial shower rooms. The insulating layer of such models is made of polyurethane foam.

The Ariston range of water heaters can have both an advanced electronics system and a simple control mechanism. The warranty on bulk tanks is given on average for seven years. For additional fastening of boilers, special metal frames are made.

Connecting the Ariston boiler

It is better if this work is carried out by specialists. The rules to follow when installing the device are given below:

1. It is necessary to inspect the safety valve, which should not have visible flaws. If they are present, then the damaged part should be replaced.
2. Plastic dowels are used to screw in screws.
3. Be sure to check all grounding elements.
4. An electric heater requires a separate power line to operate. The use of extension cords is strictly prohibited. The socket is placed in a damp place.
5. In operation, you must use the plug that came with the kit.

The Ariston 80 water heater performs the following functions :

• On/off. After switching on, the entire system starts up, which is due to the indicators lighting up, and the temperature of the water in the boiler will be displayed. If the indicators are not displayed or flashing, this indicates that the system is disabled.
• The Ariston abs vls 80 water heater has a power level adjustment function, which makes it possible to set the required parameters.
• The Ariston abs vls pw 80 water heater allows you to use the antibacterial function, which can be activated or disabled by holding the “power” button for 5 seconds.
• Possibility of adjusting the temperature using the “+” or “-” buttons in the range from 30° to 75°; The displayed indicators are not recorded. After switching on again, you need to set the values ​​again. Standard temperature values ​​are 75°, power – 1500 W.

Water heater “Ariston”

It is very important to prepare in advance all the tools and consumables for the work. Before starting installation, make sure you have the following tools:

Tools for installing a storage water heater.

• roulette;
• hammer drill with drill;
• adjustable wrench;
• spanners;
• wire cutters;
• pliers;
• two types of screwdrivers.

Consumables:

• Unipack type paste or FUM tape;
• tow;
• 3 shut-off valves;
• 3 tees;
• 2 connecting flexible hoses (if not included);
• metal-plastic pipe of the required length.
• if it is necessary to replace the wiring - a three-wire wire, a socket or a circuit breaker.

To install a storage electric heater, you will need a 32-40 A circuit breaker and a PVS 3X6 -3X8 cable.

Rules for operating a water heater

Extending the life of an Ariston brand storage heater is not difficult; you just need to install it according to the instructions and strictly follow the rules for operating the device :

• The presence of water in the boiler should be checked every time the device is turned on and off. Switching on is possible only when the tank is filled with water.
• If the power cord is damaged, it must be replaced with material of the same brand, which is best purchased at a specialized retail outlet.
• If the heater will not be used for a long period, especially in the cold season, then the water from the boiler must be drained, following all the rules prescribed in the instructions. After this, the cold water supply tap is closed. After these steps are completed, the heater is disconnected from the electricity supply.
• Over time, the heater requires cleaning from dirt. To carry out this work, it is better to use the services of specialists.

We recommend a hydraulic accumulator in a water supply system: functions and principle of operation

Reviews of ARISTON water heaters with a volume of 80 liters

For those buyers who took the plunge and purchased an Ariston water heater, the reviews remain purely positive. Below are some of them.

“Advantages: excellent “worker.” Disadvantages: none found.

Since we have a private house and no gas, it was decided to purchase a boiler. I’m tired of constantly heating water on the stove in order to buy food and even just wash the dishes. We asked friends who already had experience working with such units. They, in turn, recommended an Ariston water heater. After reading more reviews, we chose a brand like ARISTON.

We purchased a model with a volume of 80 liters. This is quite enough for a family to use. I really liked the presence of a sensor with which you can always find out the level of water temperature so as not to “get into trouble”)). This heater served us for many years, it was even sad to leave (it was removed because we installed gas and connected a double-circuit boiler). But during its service, this heater proved to be excellent: it quickly “delivered” hot water and maintained its temperature for a long time, consuming little electrical energy. In general, the model is excellent!!!”

“Advantages: compactness, fast heating of water, low electricity consumption, equipped with additional protection. Disadvantages: none.

Excellent water heater. I had to get acquainted with him when the systematic shutdown of hot water in houses began for indefinite periods. In order not to sit and wait for a “miracle,” it was decided to buy a water heater. On the advice of the seller, we purchased a heater

Ariston SG-80, which did not have a high price. And we liked his appearance too. The place for the boiler was determined in the toilet, where it did not cause any inconvenience to anyone. During use, we were convinced that we had taken an excellent assistant: it quickly heats water (80 liters in 4 hours), consumes little - 1.5 kW, heats water to an acceptable temperature - 75o, there is a safety valve and a magnesium anode. We were completely satisfied with the choice!”

“Advantages: simplicity, reliability, ease of use. Disadvantages: I didn’t find any particular ones.

An Ariston SG-80 brand water heater came into our home back in 2013, we bought it at a discount and did not regret it. My husband did the installation himself, and it turned out to be not that difficult. The heater serves the bathroom and sink. There is plenty of water, despite the fact that we set the heating level to 50o, this allows us to save a little. It takes an average of 2 hours to heat 80 liters at this temperature. I was very pleased with the quiet operation of this device. We were pleased with the purchase."

“Advantages: heating up to 75o, low energy consumption. Disadvantages: little significant, but the lid is poorly thought out.

Our small town is not connected to hot water supply. While we lived together, we got by. But after the baby was born, we decided to buy a boiler. We chose 80 liter models available at our expense. We settled on the Ariston SG 80 model, which suited us in all respects: energy consumption of 1.5 kW, volume, heating temperature, which reaches 75° and, of course, price.

Having installed it, we ourselves felt the advantages. Everything worked like a charm. It was a little inconvenient when switching the temperature when it was necessary to switch the lever under the lid. It was not entirely convenient to get a screwdriver to the right place. But this is not so significant, because we only had to change the temperature indicators once. Overall, the model is excellent. I recommend to all!"

We recommend a coarse water filter: types and installation methods

How to clean a boiler?

To clean the water heater you will need the following equipment: a knife, a flashlight and a metal brush for washing dishes. Initially, you need to disconnect the heater from the power supply. You also need to turn off the water supply throughout the house or apartment.

Then, you need to remove the cover, which is located at the bottom of the tank, and disconnect all the wires there. All water is drained from the tank through a hose attached to the drain valve. There are bolts at the bottom of the tank that need to be unscrewed, while replacing any container.

To thoroughly clean the boiler, the electrical part is removed from it. You need to remove it very carefully so as not to snag the rubber gasket. The removed electrical part must be cleaned with a special iron mesh or a certain chemical.

The next cleaning step is to remove scale and debris from the tank. To do this, you need to completely inspect the tank cavity (using a flashlight) and clean out all the debris by hand.

The cleaned tank must be thoroughly dried, after which it can be assembled to its original state. Also, before starting work, you should check the tightness of the tank.

If the rubber gasket does not allow water to pass through, then the boiler can be put into operation.