How to connect an Ariston 10 liter water heater

Turn on Thermex

Depending on the design of the water heater, some steps may vary. This mainly depends on the type of device - flow-through or storage. Meanwhile, there are several basic principles that are applicable to any type of water heating equipment, including not only the Thermex brand.

The universal instructions for turning on the boiler consist of three steps:

1. The first step is to shut off the supply of hot water from the central water supply. If there is a check valve on the hot water pipe, you still need to shut off this branch. This is done so that even with a slight leak, boiling water does not flow into the central line.
2. In order to displace air from the system, the hot water tap on the device is opened, then the mixer is opened and cold water is supplied. After the water flow begins to flow smoothly, the mixer is closed and the boiler is filled with water.
3. The last step is to connect the device to the network, set the required values ​​and wait about an hour before using it.

Instantaneous water heater Source cdn.amzu.ru
With instantaneous type heaters, the procedure is similar, except that boiling water will flow almost immediately.

An important step in operating a boiler is checking its functionality. When connecting to the network, you need to make sure that all indicators are illuminated. Measure the initial temperature of the water in the mixer. After about 20 minutes of operation of the device, take another control temperature measurement, making sure that heating is taking place. On devices with a touch panel, manipulations with the thermometer are not required; all data is displayed on the screen.

See also: Catalog of companies that specialize in heating and other engineering systems for private homes

Models and displacement

Model line:

1. VELIS INOX.

Original characteristics:

• stainless steel elements, including tanks;
• the characteristic difference is universal (simple) installation;
• flat shape;
• Ariston water heater is available in 30, 50, 80 and 100 liters;
• there is a protection system on the power cord;
• fuse against starting with an empty container;
• additional equipment is equipped with protection against freezing or overheating;
• branded heating elements are made of high quality copper;
• load distribution function due to flasks and two heating elements of 1 and 1.5 kW;
• maximum power 2.5 kW.

1. ABS VLS INOX QH

Externally similar to VELIS INOX, but has differences:

• Ariston water heater for 30, 50, 80 and 100 liters;
• improved design solutions;
• equipped with electronics for fast heating, antibacterial water purification (ECO), temperature measurement;
• The water is processed in two tanks; for rooms with a large area, an Ariston water heater of this model with a capacity of 100 liters is recommended.

1. VELIS QH

Has external similarities with ABS VLS INOX QH and VELIS INOX.

Model differences:

• super-fast heating;
• ease of design and use;
• LCD – display;
• soft touch function (automatic saving);
• the water is heated in several stages;
• internal tanks are covered with steel;
• three heating elements (heating elements);
• Ariston water heater for 30, 50, 80 and 100 liters.

1. ABC VELIS PW

Original characteristics:

• Ariston heaters for 30, 50, 80 and 100 liters;
• safety shutdown (ABS0);
• bacterial protection (ECO);
• the internal tank is covered with the latest AG+ technology;
• special welding method during the assembly process;
• two heating elements;
• heating in two containers.

1. PRO ECO INOX PW V SLIM

Original characteristics:

• Ariston heaters for 30, 50, 65 and 80 liters;
• water-pressure function;
• stainless steel;
• SLIM model, diameter only 353 millimeters;
• internal tank with special antibacterial coating;
• installed at points with cold water pressure, any pressure level is suitable;
• low power (up to 1.5 kW).

1. ABS PRO ECO INOX PW

Original characteristics:

• Ariston heaters for 50, 80 and 100 liters;
• narrow cylindrical shape;
• simple installation;
• electronic control;
• external and internal parts made of stainless steel;
• testing at 16 atmospheres;
• 7 year warranty.

1. ABS PRO R INOX

Original characteristics:

• mechanical thermostat;
• Ariston heaters for 30, 50, 80 and 100 liters;
• an anode with a magnesium composition is installed to protect against corrosion and scale concentration;
• external heating control;
• protection against water drops;
• waterproof;
• one of the most economical models.

1. ABS PRO ECO PW SLIM

Original characteristics:

• Ariston heaters for 30, 50, 65 and 80 liters;
• narrow forms of water heater;
• economical energy consumption, the tank of the model was tested for strength under pressure of 16 atmospheres, a good margin of safety;
• equipped with all protection systems.

1. ABS PRO ECO PW

Original characteristics:

• Ariston heaters for 50, 80, 100, 120, 150 liters;
• suitable for a kitchen sink, a full-fledged house or cottage;
• equipped with all protective security systems;
• additional heating element.

1. ABS PRO R SLIM

Original characteristics:

• the convenient shape of the cylinder allows you to mount the heater in any corner of the room;
• Ariston heaters for 30, 50, 65 and 80 liters;
• “folk”, budget water heater suitable in size;
• diameter 35 centimeters;
• fast heating;
• presence of a safety valve;
• all water protection systems, switching on without water;
• the price for an Ariston water heater of this model of 80 liters is only 8800 rubles.

1. Ariston ABS VLS PW 50

Original characteristics:

• instant heating;
• practicality;
• compactness;
• affordable;
• possibility of horizontal and vertical hanging;

Problems with inclusion and their solutions

When faced with a connection problem, first of all, you need to check the electrical network and terminals of the device. The boiler has a lot of power and a poorly installed socket often burns out. It is worth checking the automatic protective shutdown, as well as “ringing” the terminals of the device with a tester.

A fairly popular question is how to turn on the Thermex boiler if there is a system error. This applies to devices with a touch control panel on which an error code is displayed. In this case, the instructions for the device will help, listing the meanings of all code messages. In case of its absence, we list the most common problems:

• a burnt-out heating element coil, the main sign is that the body of the device is electrocuted;
• thermal protection is triggered when the thermostat is broken or there is a large layer of scale on the heating element;
• empty tank or presence of air in the pipes.

Heating element for a boiler Source mydetail.market
The first two problems are solved by replacing faulty components or cleaning the heating element. The third is the easiest and can be solved by filling the tank with water and bleeding air from the system, as described above. Now you know how to turn on the THERMEX water heater, let's move on to the next device.

Climate

A water heater is an excellent solution for providing hot water. However, it is recommended to install such a device near water intake points. If the bathroom and kitchen are located in different parts of the house, then it is preferable to install an individual water heater for each of them. Small and compact models fit easily under the sink. We will learn further about the features of installing a boiler with your own hands.

Table of contents:

Do-it-yourself boiler under the sink: features of choice and varieties

A water heater installed under a sink consists of the same elements as a regular boiler. The only difference is the smaller size and power of the device. It also has two pipes that connect it to the cold water supply system and the hot water supply system.

The storage tank of such a water heater is compact in size and easily fits under the sink. When choosing a water heater, first of all decide on the optimal amount of water needed for washing dishes. If your family is small, then a ten-liter device is quite enough. This option is quite suitable for a family of two, maximum three people. It is possible to install both instantaneous and storage versions of the water heater.

The second option is to install a tank with a capacity of fifteen liters. It is suitable for a family of two adults and one child. The most optimal is a boiler with a capacity of twenty liters. With its help, it is possible to heat water for a family of four.

Some manufacturers make kitchen boilers with a capacity of twenty-five liters or more. If you use water only for washing dishes, but not for taking a shower, then purchasing this device will not be advisable. Since you will spend a lot of money on paying for electricity, which is spent on heating so much water.

Depending on the type of structure and principle of operation, water heaters for sinks are:

• flow-through;
• accumulative type;
• bulk type.

The first option assumes the presence of a key water heating point. Water passing through the device quickly heats up and is supplied outside. The power of such mechanisms ranges from three to eight kilowatts. These types of boilers are divided into closed or support type devices. Among the advantages of instantaneous boilers, we note:

• compactness;
• lack of tendency to scale formation;
• fast water heating;
• high power, which increases the energy costs of operating the device.

If you need to stock up on hot water in reserve, then it is better to opt for a storage type of heater. This option allows you to heat a certain amount of water. Sink appliances vary in capacity from ten to thirty liters.

Such devices require the installation of additional filters that help fight scale. In addition, the heating elements must be cleaned.

When choosing a water heater for a sink, you should consider the following factors:

1. The power of the device, which affects the amount of electricity.

2. The thickness of the thermal insulation material, which determines the degree of water cooling.

3. Type of device.

4. Place of installation - in this case, the sink.

5. Type of premises and housing - cottage, house or apartment.

6. Volume of water consumption.

If you are choosing between water heaters of the same volume, and one of them is larger in size, then we recommend choosing this option. Since this model has a thicker thermal insulation layer, which prevents the water from cooling down during the heating process.

How to install a boiler with your own hands

Installing a boiler is a fairly simple process, which, first of all, requires compliance with all technological aspects of its implementation. First, after purchasing the device, you must study the instructions from the manufacturer. It describes in detail the type of fasteners and installation features of the device.

Next, you should prepare the water supply system for installation work. Install a shut-off mechanism on the cold water supply pipe, which can be used to stop the water supply in the future. In addition, you will need to install a check valve. We recommend connecting the water heater to a water supply system made of metal-plastic pipes.

Initially, a cold pipe should be installed. A check valve is mounted on it, preventing hot water from entering the cold water supply. One side of this pipe is equipped with an internal thread, and the other is equipped with an external thread. Therefore, the installation process is quite simple. A tap is installed on the valve, the second part of which is equipped with an adapter for connecting to a pipe made of metal-plastic.

A hot pipe involves installing only a faucet and an adapter to a metal-plastic pipe.

Prepare the water supply system for installation work. To do this, connect the mixer to cold and hot water supply. Take it apart and connect each hose individually. Install shut-off valves for water outlet. Install tees on the taps; they must be equipped with both internal and external threads. After this, we move on to the next stage of installation work - laying the electrical wire.

For these purposes, either a carrying cable is used or an additional wire is installed directly for the water heater. It must be equipped with a separate safety device. Since the capacity of the tank is quite decent, it is also necessary to install a protective shutdown device. Be sure to ensure proper grounding of the device.

Turning on "Ariston"

Since the basic steps for turning on boilers, regardless of manufacturer and brand, are the same, answering the question - how to turn on an Ariston boiler, once again, briefly, we will go through all the steps:

• the supply of boiling water from the central system is closed;
• the hot water tap on the boiler opens;
• the mixer opens;
• cold water is supplied to the heater tank;
• air is bled from the system;
• the device tank is filled;
• the boiler is connected to the network and turned on;
• diagnostics of the device operation is carried out.

For Ariston heaters, the manufacturer’s recommendation is to set the heating temperature to the average value when first starting. As you use it, the heating is adjusted depending on your needs. It is claimed that this approach saves energy.

Standard instructions for an Ariston water heater 80 liters

Water heaters of this size are necessary for daily use by the whole family. The presence of sensors and temperature levels guarantees safe operation.

A complex and important event during the installation process is the installation of electrical wiring. Most often, the wires need to be extended because the factory cable is not long enough.

For long-term use of the device, it is necessary to carry out installation in accordance with all the rules or with the help of an experienced technician. To avoid breakdowns and other hassles, follow the operating rules:

1. The first switching on and off should be carried out with a full tank.
2. If the batteries are damaged, be sure to replace the weak parts.
3. In a room with sub-zero temperatures, it is necessary to drain the water from the heater.
4. Leaving the device idle for a long time without a heating function should be done with the water supply tap or valve closed. Heaters must also be unplugged from the outlet.

Devices for high-quality water heating from Ariston are presented in user-friendly sizes, equipped with all kinds of engineering improvements and are available in all major retail chains. All you need to do is select the model you need for individual installation.

How to connect the boiler correctly

How to connect a boiler to your water supply system and start using it for your needs? This question has probably been asked by everyone who has ever encountered problems with a stationary hot water supply.

Unfortunately, the reality in our area is that residents of not every house have the opportunity to use all the benefits of civilization, including hot water directly from the water supply system. Very often, water heating for water procedures must be organized independently, by installing water heaters or boilers.

Rating of TOP 7 best models

How to choose and what to pay attention to?

The devices provide the household needs of a family of 2-3 people.

Therefore, when purchasing a unit, you should consider the following factors:

• power - the heating time will depend on it;
• water preparation speed - some models can heat the liquid from 20 to 30 minutes;
• additional features - many devices are equipped with a touch screen, protection against overheating and sudden surges in voltage, automatic modes, and so on;
• service life and cost - the period of operation is indicated in the technical data sheet of the water heater.

The following are popular models from well-known manufacturers.