How to turn on a floor-standing protherm gas boiler

Page 11

Warning:

Commissioning of the boiler and its first start-up must only be carried out by a certified

by Protherm, a specialist from a specialized organization!

When starting the boiler for the first time, make sure that:

1. the boiler is connected to the electrical network and

in this case, the phase and zero are not mixed up.

2. gas shut-off valve is open; 3. service taps for heating and hot water supply

4. The pressure in the heating system is

within acceptable limits 1 - 2 bar. Set the main switch (Fig. 1, item 7) to the ON position (I). The boiler will turn on and start operating in the boiler water heating mode (if the boiler is connected to the boiler). After heating the water in the boiler, the boiler will switch to heating mode (provided that heating mode is active). In case of protective

When the boiler is turned off, a fault message will appear on the control panel display (see “Error messages”, page 8). Using the RESET button (Fig. 1, item 6) unlock the boiler. If, after switching on, the protective shutdown repeats, or it is impossible to unlock the boiler, contact a service organization.

If the boiler is switched off for a short time, set the main switch (Fig. 1, item 7) to the OFF (O) position. When turning off the boiler for a long period, it is necessary to disconnect it from the electrical network and shut off the gas supply to the boiler. If the boiler is not used in winter, the heating system must be emptied. However, it is necessary to avoid frequent draining and top-up of the heating system to avoid the formation of scale and deposits inside the boiler.

Starting and shutting down the boiler

Operating the boiler without a room regulator

In this mode, the boiler maintains the set temperature in the heating system according to the readings of the boiler sensor. In the XT5 terminal block there is a jumper on terminals 5 and 6 (factory setting). Setting procedure:

• turn on the boiler with the main switch; • set the required temperature

flow line on the control panel.

Operating a boiler with a room thermostat

In this mode, the boiler maintains the set temperature in the heating system using the room regulator. The jumper installed in the XT5 terminal block at terminals 5 and 6 is removed. A room regulator is connected in its place. If thermostatic valves are installed on the radiators in a room with a room regulator, they must be set to the fully open position. Warning:

On the control panel

Malfunction of the external temperature sensor

The boiler operates without restrictions, but the temperature

The heating medium is regulated by the boiler sensor (see “Setting the heating temperature”, page 5).

If the boiler is not operating in equithermal mode, such a message cannot appear.

The well-known company Protherm was founded in Slovakia in 1991. And almost from the first day of its appearance on the market, the company has established itself as a manufacturer of high-quality and reliable equipment for heating systems. But the emphasis was placed both on product quality and on the creation of new boilers in accordance with consumer demand and market trends. When developing new products, the company not only satisfies, but also anticipates the needs of the end consumer. More than a hundred types of gas boilers are manufactured today under the Protherm brand, and in considerable quantities. It is characteristic that Protherm gas boilers are more popular, so the company pays more attention to them.

Technical characteristics of electric boilers Proterm Skat

The main products of this company are boilers of the Proterm Skat model of various capacities. They all have similar technical characteristics. Overall dimensions are: height - 74 cm, width - 41 cm, depth - 31 cm. The device operates from both three-phase and single-phase networks. The maximum permissible current in them is 50 amperes. The highest pressure in the system is up to three atmospheres, the coolant temperature is about 85 degrees.

Important! When connecting heating systems to the network, their power consumption must be taken into account and suitable wires must be used. This will protect them from melting and burning out, increasing their service life and ensuring safety.

Types of gas boilers "Proterm"

Gas equipment from this manufacturer is manufactured in the following modifications.

1. Boilers of the “Gepard” model are wall-mounted appliances in which the coolant moves forcibly.
2. “Tigers” are double-circuit boilers, which are also wall-mounted, but are equipped with an electronic control system.
3. The advantage of the Grizzly and Bear boilers is that they are equipped with automatic control of the combustion process. Another distinctive feature is the special ignition system.
4. "Lynx" and "Leopard" have a bithermic heat exchanger. In general, they are also double-circuit.
5. Finally, for the “Panther”, a wall-mounted heating device, the developers have provided for the ability to work in closed heating systems.

The main advantages of Proterm boilers

As you know, you can heat a house not only with gas, but also with diesel, etc. And if at the moment you need a diesel boiler, but in the future you plan to switch to gas, then it is not necessary to buy two heating devices, because Protherm gas boilers are sold today.

Of course, each model has a different power, but they still compare favorably with other boilers in this parameter. The fact is that they can be used to heat rooms with a total area of ​​270 square meters. In addition, all products of this brand are easy to use and install, and this is an ideal option for those who value safety first. And it’s not surprising, because all boilers of this brand fully comply with European and world standards.

Note! It is worth adding that all Proterm heating devices have another amazing characteristic - unusual fuel combustion. Even experienced experts are surprised at how environmentally friendly this process is in this case.

Consumer Reviews

Consumers note that Protherm Skat provided an opportunity where gas connection was problematic or completely impossible. When the power grid is stable, many people refuse to connect to gas, saving considerable amounts of money. In addition, an electric boiler is used in parallel with a gas unit, connecting them to a single heating system. This find allows you to significantly save money on resources by alternating them with each other during the heating season.

If you connect a water heater to Protherm Skat, consumers have the prospect of using hot water. Many people note the perfectly designed design of the boiler, which fits well into any room interior. It can be successfully installed in living rooms; thanks to its silent operation, it will not cause increased attention.

The disadvantages are that when using only a boiler that runs on electricity, there are no alternative heating options when it turns off. Therefore, before purchasing a Protherm electric boiler, you should make sure that there are no problems with electricity. Experts recommend using a voltage stabilizer to ensure normal operating conditions for the Protherm Skat boiler.

In addition, the increased energy consumption of an electric boiler causes negative emotions among the population, since paying bills takes a toll. If we compare the costs of gas and electric heating, the Protherm electric boiler is a little more expensive, with identical heating parameters. From the above, we can conclude that this electrical equipment is chosen by those who do not have the opportunity to connect to network gas, as well as by those who care about the environment and see it as a source of environmental consumption.

Protherm wall-mounted boilers

Let's start with the most popular model - the Tiger.

Model "Tiger"

The power of the heating equipment of this model varies between 3.5 and 23 kilowatts. All devices are economical and reliable, developed in accordance with the latest trends in technology and design. They also comply with all standards and requirements for heating systems.

“Tigers” are equipped with a 25-liter boiler, which has a unique “Spin” system and a temperature sensor for hot water supply. Thanks to all this, boiler owners receive not only high speed and efficiency, but also constant hot water. The technical characteristics in this case are as follows:

1. the device is reliably protected from frost;
2. the pressure in the system is read using a special electronic device;
3. it is quite possible to place the device in the bathroom;
4. heating and hot water parameters are configured separately;
5. power is adjusted smoothly;
6. the boiler is protected from possible overheating;
7. built-in microprocessor;
8. a special display displays the main operating parameters;
9. There is a pump protection function that prevents jamming.

The approximate cost of "Tigers" varies between 60.5 and 90.5 thousand rubles , depending on the specific variety.

Model "Scat"

The gas unit called “Scat” is characterized by a modern design, stepwise power adjustment, low noise output and ease of operation. All devices are quiet and require virtually no maintenance, and are used mainly in apartments/houses of small areas. Comply with all safety standards, environmentally friendly (do not harm the environment). For this reason, they can even be used in protected areas!

Finally, such Protherm gas boilers are easy to maintain and can warm up the room almost instantly. The average cost of “Scats” ranges from 26.3 to 152 thousand rubles.

Model "Panther"

This particular model is distinguished by the fact that it has a special “Comfort” function, which provides extremely fast heating of the water. There is a built-in microprocessor, an “i-BAS” communication bus, it is possible to adjust the boiler power, control of all parameters is convenient and simple, since it is adjusted on the monitor. There are two heat exchangers, as well as electric ignition.

All “Panthers” can be classified as middle class gas heat generators. They are capable of heating and heating water not only in private homes, but also in offices, apartments and other premises. "Panther" is produced in three models:

1. devices with a sealed combustion chamber (28-KTV);
2. 24-KTV;
3. devices with an open combustion chamber designed for two circuits (24-KOV).

In terms of hot water supply, the performance of this model ranges from 12-15 liters, and the area of ​​the heated room can reach 270 square meters. The possibility of functioning in low pressure conditions is provided.

It is worth mentioning special protective functions, including:

1. preventing system freezing;
2. gas supply shutdown;
3. anti-cyclicality of the heat generator;
4. preventing pump jamming.

The approximate cost is from 35.2 thousand rubles.

Video – “Panther”, 24-KTV

Model "Cheetah"

All boilers of the “Gepard” model are not too different from similar middle-class appliances. They have fairly low functionality, although they are relatively inexpensive. To adjust the power of the device, a special modulation burner is provided. If we talk about efficiency, then during the heating season it can reach 92 percent. As in the previous version, there is an “i-BAS” communication bus.

The functions of "Cheetah" include:

1. ability to select operating mode (summer or winter);
2. adjusting performance using the monitor;
3. heat exchanger made of stainless steel;
4. working fluid pressure sensor;
5. diagnostic system;
6. burner, which is made of chrome-nickel steel.

The approximate cost is from 32.2 thousand rubles.

Video – “Cheetah”

Advantages and disadvantages of electric boilers Protherm Skat

Proterm Skat has a number of advantages over other types of heating:

• does not produce harmful emissions into the atmosphere, since it has no combustion products , so this type of heating can be called environmentally friendly;
• An electric boiler is an affordable type of heating. It is used where it is not possible to connect to mains gas or can become an alternative form of heating;
• does not require systematic maintenance, unlike, for example, gas or solid fuel models;
• silent operation;
• there is a heat level regulator;
• able to adapt to domestic water of poor quality;
• resistant to voltage surges;
• equipped with several types of protection.

Along with the advantages, there are some disadvantages:

• electric boiler Protherm Skat needs to be connected through a stabilizer;
• is unable to perform its work during a power outage.

Proterm devices with bithermic exchangers

This class is represented by only two models; let’s take a look at each of them.

Model "Lynx"

Protherm gas boilers of this model are dual-circuit combined equipment intended for both heating residential premises and supplying hot water. Known for their uninterrupted and reliable operation, excellent quality/price ratio, excellent efficiency, ease of operation and low noise output.

Here are the main properties of the structural elements that the Lynx is equipped with:

1. smooth power adjustment;
2. display of basic operating parameters on a special display;
3. protection of the device from severe frosts;
4. built-in microprocessor;
5. valve for additional supply of working fluid to the system;
6. regulated using a bypass valve;
7. separate filters for heating fluid and hot water supply;
8. effective protection against overheating.

The approximate cost starts from 30.5 thousand rubles.

Model "Leopard"

The average power of Leopards ranges from 8-24 kilowatts. All devices in this line are characterized by high efficiency and cost-effectiveness. Produced in two variations:

1. with an open combustion chamber;
2. with closed.

The productivity in terms of hot water supply is 12.5 liters per minute, and the area of ​​the heated room can reach 220 square meters. You can adjust the power, as well as other operating parameters, directly from the panel. Excellent performance even in low pressure conditions, which is especially important in today's times when fluctuations in gas supply occur quite often.

Each of the Leopards, if necessary, can be converted from natural gas to bottled gas. To do this, you do not need to perform complex manipulations; you just need to change the gas valve and nozzle.

Protective functions include:

1. antifreeze;
2. anti-cyclicality of the heat generator;
3. anti-inertia of thermal energy.

Device

The design of Protherm floor-standing boilers consists of the following components and parts:

• Cast iron primary heat exchanger.
• Gas burner (2-stage or modifiable).
• Gas valve.
• Three way valve.
• Turbocharger fan.
• Circulation pump.
• Indirect heating boiler.
• Control board, sensor system, external panel with display.

The principle of operation of floor-standing boilers does not differ from the generally accepted scheme. The coolant enters the boiler and is heated in the heat exchanger to maximum temperature.

Then it enters the indirect heating boiler (if there is one), where it releases part of the thermal energy to prepare hot water. After this, a cooler return flow is mixed into the three-way valve to obtain the coolant at the required temperature.

Then the heating agent is removed from the boiler into the heating circuit, after which it cools and re-enters the boiler.

Protherm floor-standing boilers

Let's not beat around the bush - let's move directly to the characteristics.

Model "Bear"

Excellent cast iron equipment that can be used not only as the main, but also as an auxiliary heat source (for example, in addition to a solid fuel boiler). It is known for high-quality cast iron, thanks to which the service life is significantly increased. The advantages also include uninterrupted operation and ease of operation.

Special parameters of gas boilers:

1. traction control;
2. if you install a semi-turbo superstructure, then a chimney is not needed at all;
3. operating modes “Winter” and “Summer”.

The approximate cost is from 40 to 117.2 thousand rubles.

Video – Bear KLOM

Model "Bison"

Reliable and durable boilers that operate not only on gas, but also on fuel oil and diesel fuel. Increased efficiency, large power range. They are used where power is required, which is measured in megawatts.

1. impressive efficiency;
2. environmental friendliness;
3. ease of care and use;
4. consumption of alternative fuels;
5. long service life of the heat exchanger;
6. DHW is heated in a separate tank.

The approximate cost is from 55 to 130 thousand rubles . So we looked at the main Protherm gas boilers. Warm winters and good luck at work!

The Protherm gas boiler is produced by the famous company Protherm, founded in Slovakia more than a quarter of a century ago. The model range of this manufacturer is characterized by a successful combination of heating power levels and energy efficiency indicators.

Model range of Protherm boilers - single-circuit and double-circuit

Gas equipment Proterm is produced by a European manufacturer in several modifications, which allows you to choose the model that is optimal in terms of functionality, as well as practical and most convenient to use.

Wall type

Wall-mounted gas equipment has undeniable advantages, including compact size, external aesthetics, excellent performance properties, the ability to adapt to operation with different energy carriers through a standard replacement of the nozzle, as well as cost-effectiveness.

• "Panther". Inexpensive model with two heat exchangers for space heating and water heating. A modern heating device with the ability to operate in a closed system. It has reliable protection against freezing, automatic shutdown of gas supply and control of pump operation.

Inexpensive heating device option in the Protherm line

• "Jaguar". A budget option for equipment that does not have a winter/summer mode. Double-circuit unit with a closed combustion chamber and control via handles.

A simple model with the minimum required set of functions

• "Cheetah". Double-circuit turbocharged boiler with a power of 11–23 kW and a closed combustion chamber. Even low-power models can heat 10–11 liters of water in one minute. A wall-mounted device in which the movement of the coolant is forced.

Turbocharged boiler with high efficiency

• "Tiger". It features a neat appearance, an informative LCD display and very simple controls. It is possible to program it for different operating modes or operate in automatic “comfort” mode. It is possible to automatically regulate the combustion process and is distinguished by a special ignition system.

Compact equipment with different operating modes

Main characteristics of the boiler

Floor type

Floor-standing single-circuit and double-circuit boilers have several advantages that make this type of equipment in demand among consumers. It is impossible to ignore high performance indicators, maximum thermal efficiency, economical fuel consumption, wide functionality and guaranteed durability.

• "Bear". A high-quality cast iron heat exchanger makes the unit durable and very reliable. The model has a “Winter-Summer” mode and convenient traction control. It has automatic regulation of the combustion process and is distinguished by a special ignition system.

The cast iron heat exchanger ensures long-term operation of the boiler

• "Buffalo". Easy to use and durable boiler with high efficiency, capable of operating on different types of fuel. A very powerful unit with a high degree of reliability.

Powerful equipment that can operate on different types of fuel

Main characteristics of the Bison model

Floor-standing boiler with a reliable heat exchanger

Main characteristics of the model

Stationary heating gas boiler

Main characteristics of the model Bear KLOM17

Technical characteristics and appearance

The Proterm electric boiler will fit into any interior due to its small size and wall placement.

As befits good equipment from a well-known brand, Proterm electric boilers are housed in neat, compact housings. Thanks to this, they can fit into any interior , even the most sophisticated. Case dimensions – height 740 mm, depth – 310 mm, width – 410 mm (dimensions are identical for the entire Skat model range). Inside we will find everything you need for the heating system to work:

• Circulation pump;
• Automatic air vent;
• Expansion tank 7 liters.

There is no need to worry about installing the piping - just connect the pipes and radiators, fill the system with coolant, after which you can start testing.

Models with a power of 6 kW and 9 kW can operate from both single-phase and three-phase networks. More powerful ones are three-phase. The equipment is not afraid of power surges and does not cause overloads on the network - a stepwise increase in power is provided here. The maximum current in the circuit when the heating elements are operating is up to 50 A. The maximum coolant pressure in the system is 3 atm, the temperature is up to +85 degrees.

Layout of inlets for Proterm electric boilers, as well as their dimensions.

Protherm electric boilers are equipped with convenient control panels. They contain LED indicators and liquid crystal displays. Self-diagnosis systems are provided - error codes are displayed on built-in screens. Thermostats are used to create a comfortable atmosphere. Safety systems include an overheating sensor, frost protection, a pressure sensor, a safety valve and an anti-blocking system for the circulation pump.

Construction of a Proterm gas boiler

Various modifications of gas equipment have individual characteristics of the device.

Manufacturing boilers using low-temperature cast iron helps to effectively minimize heat losses. A special feature of the design of heating devices of the Proterm brand is also an unusual, fairly environmentally friendly method of burning fuel.

The main components of gas heating equipment are presented:

• ignition system;
• burner;
• heat exchanger.

The heat source is represented by the flame of a burner in which gas is burned, and a heat exchanger is responsible for heating the coolant. The gas supply process is regulated by a thermostat, while combustion products, represented mainly by water vapor and carbon dioxide, are discharged through the chimney system.

Proterm boilers are used for heating and hot water supply

Construction of electric boilers

The Skat boiler is equipped with all the necessary modules to ensure a complete heating process:

• Cylindrical heat exchanger made of copper.
• Also copper heating elements. Their power is different to create a multi-stage heating system.
• Expansion tank, volume 7 liters. Performs the function of compensating for the expansion of coolant in the system.
• To carry out forced circulation of coolant in the system, the design has a special pump with three speeds.
• The air accumulated in the system is automatically removed through a special air vent.
• The hydraulic group also has a pressure relief valve to maintain a maximum pressure of 3 atmospheres.
• Thermostat.
• A group of sensors that protect the device from freezing, overheating, and blocking the circulation pump.

How to connect and configure

Basic conditions for installing gas heating equipment from:

• installation of the boiler and the necessary auxiliary equipment is carried out in accordance with the design documentation, taking into account the requirements of SNiP and the manufacturer’s recommendations;
• installation of equipment is carried out in a room specially designed for these purposes, and in case of special modification of the unit - exclusively in well-ventilated outbuildings;
• the installation and commissioning process is carried out by specialists who have completed a training course in the installation and maintenance of gas equipment;
• any boiler malfunctions are repaired by a service organization authorized by the manufacturer of heating and water heating equipment;
• independent installation work entails deprivation of the consumer's warranty on the unit and its repair;
• When unpacking heating equipment, the supplied boiler must be checked for completeness and compliance with the type of fuel used.

Before proceeding with installation, you must carefully read the instructions supplied with the gas boiler, and during the installation process all recommendations given in the accompanying documents must be followed. Markings on equipment must not be damaged or removed.

How to set it up correctly

Setting up a gas boiler involves setting the lower and upper limits of gas and water pressure, as well as determining the temperature limits for starting and stopping the burner. These parameters are set based on the operating conditions of the boiler, the ratio of its power and actual load, and other considerations.

It is not recommended to set the difference between the lowest and highest coolant temperature values ​​too small, as this will cause frequent starting and stopping of the boiler, which can lead to failure.

The pressure limits of water and gas are usually set within the limits inherent in the technological conditions of a given network.

Brief operating instructions

Proper adjustment of Protherm gas boilers ensures optimal temperature conditions in rooms of different purposes and sizes. Among other things, the regulation of the automation of such equipment helps to increase the efficiency of the unit, and also makes its operation reliable and safe. Modern automation solves problems:

• opening and closing valves in the gas supply system;
• the process of starting the unit in automatic mode;
• established or emergency shutdown of boiler equipment;
• adjusting the flame level in the burner using a temperature sensor;
• display on the screen of air temperature, coolant heating level and other parameters.

Instructions for setting up a gas boiler:

• connecting a thermostat to a temperature sensor recorded in the room and setting the required values ​​allows you to obtain a comfortable heating temperature;
• installation of a thermostatic valve on supply pipes in front of heating radiators helps to change the cross-sectional area of ​​the pipe and easily carry out the process of regulating the temperature of the coolant;
• the first start of the system at the maximum temperature allows the coolant used to freely enter the tank, which contributes to its maximum filling;
• Increased efficiency is facilitated by timely removal of scale and soot, as well as monitoring the lack of air in the system and installing a draft limiter;
• regulation of pressure indicators is carried out using special valve regulators, and in order to increase the pressure, a circulation pump is installed;
• reducing the power of the boiler burner is carried out automatically through the service menu, and increasing power is controlled by installing additional radiators or replacing existing ones with the most powerful models;
• many units are characterized by full operation at a pressure of 1.5 atm., and normally this value is 0.3 atm. lower than the indicators in the heating system;
• a slight decrease in the pressure level in the unit is restored during a standard restart;
• automatic selection of the operating mode of the gas boiler helps maintain the desired temperature level even in the absence of consumers in the room for a long time.

The process of turning on the boiler for the first time is accompanied by its short and vigorous operation after the unit is fully connected to the heating system, making it easy to check the correct installation of the boiler equipment and the full functioning of the heating.

Types

There are various modifications of Protherm floor-standing boilers:

• Single-circuit . They are only capable of heating the OM for the heating circuit. Most models have the ability to connect an external boiler to prepare hot water.
• Dual-circuit. They simultaneously heat the coolant and prepare hot water (DHW) in flow mode.

In addition, there are models with an open (atmospheric) or closed (turbocharged) burner. Atmospheric structures use natural draft to remove flue gases.

Turbocharged boilers use special fans to supply air and create draft..

NOTE!

Existing double-circuit models of floor-standing boilers prepare hot water in a flow-through mode, so they are not suitable for providing a large number of water collection points. In such cases, single-circuit models should be used in conjunction with a boiler.

Common errors and malfunctions

Some of the most common malfunctions of gas boilers can be eliminated independently, but the correction of the most complex errors must be entrusted to service center professionals.

Modern heating equipment from a manufacturer from Slovakia, the category of which includes single- and double-circuit gas boilers Protherm, is distinguished by its high reliability and variety of models. These high-quality and inexpensive boilers of European quality from the “middle class” are deservedly popular and are invariably in demand by domestic consumers.

Preparation for start-up and start-up of the boiler.

Find the controls you need:

– Piezo igniter button to supply a spark (shown in GREEN in the diagram);

– Burner control knob (shown in RED in the diagram);

– Inspection window (shown in YELLOW on the diagram);

The gas valve control is simple. To start the boiler, you need to turn the handle to the desired position and simultaneously press the piezo igniter until the wick lights up.

Please note: at the end of the handle you can see three modes: